Choco-raspberry millefeuille

 
                       Choco-raspberry millefeuille

Beautiful woven bookmark..

                         Beautiful woven bookmark..

Diy Braclet..;)

 Diy Braclet..

:))))))))))))))))))))

FREE OWL PATTERN

                     FREE OWL PATTERN

INSTRUCTIONS:

Step 1

Cut out your Tummy, Base and Body from your chosen patchwork fabric scraps. Cut out your Beak, Eye Colour, Eye White and Eye Black from felt scraps. Decide whether you wish to do felt wings or fabric wings, cut out 2 pairs from your chose material using the relevant template. Cut your Base Template out of plastic such as template plastic or a clean ice-cream container lid.

Step 2

Pin and stitch one side of the tummy piece to body piece matching and finishing at the black dots marked ‘A’.  Repeat for the other side of the tummy attaching it to the other side of the body.

Step 3

Fold the body in half and sew the seam between dot ‘A’ and dot ‘B’. Turn the body right side out.

Step 4

Use a needle with strong thread to sew a gather stitch around the bottom opening of your owl’s body. Draw up the thread a little and stuff the owl  but avoid stuffing the top of the owl as this part will fold down to ‘shape’ your owl.  Finishing drawing up the gather stitch and tie securely leaving an opening no greater than 1 & 1/2 inch wide.

Step 5

Sew a gather stitch around your base piece. Draw in your gather stitch just a little, then place your plastic base in the middle of your fabric base and draw your gathered in tight around it. Tie off your thread tightly.

Step 6

Position your base over the opening at the bottom of your owl. Stitch your base down to cover the opening until you get three quarters of the way around. Add extra stuffing if required and then finish stitching the seam closed.

Step 7

Fold the top of your owl down to shape the head. Tack the point in place with a couple of stitches. Now, take your felt beak piece and position this over the point. Stitch in place.

Step 8

Take an Eye White piece and use the paper template to mark the center point with a marker. Position the Eye White on the top of an Eye Colour piece and stitch in place with top-stitch thread. Repeat this step for the second Eye White and Eye Colour pieces.

Step 9 Take one of your Eye Black pieces, place and stitch it in the center of your Eye White and Colour piece. Repeat this step for the other eye pieces. NOTE: You could use black buttons instead of the black felt piece too, I just avoid using buttons on toys intended for children under 2 years or for pets.

Step 10

Pin both completed eye pieces to your owl, positioning them one either side of the face next to the beak. When you are happy with the position of the eyes, stitch them to your owl’s face.

Step 11

Your little owl is almost finished! The last thing we need to do is to make his wings. You can make the wings 2 different ways. The first way is to make the wings from fabric:

Fabric wings

Take two fabric Wing pieces and pin them right sides together. Using the template as a guide, sew around the wing leaving an opening. Trim your seams back by half and clip carefully into the curves so that they sit flat later. Turn your wing right side out through the opening. Press your wings with a hot iron to neaten the seams. At this point, add a little stuffing to the wing if you wish. Stitch the opening closed. Repeat this process for the second wing.

Felt wings

Take a felt wing piece and embroider your desired design. Take another felt wing piece (the one you want as the underside) and pin it to the back of your embroidered wing, wrong sides together. Neatly stitch around your wing with a decorative stitch of your choice and note that the back stitching will be visible on the underside of the wing. Repeat this process for the second wing.

Step 12

Now to attach the wings to your owl. Use a pin to position your wings either side of your owl’s body. You can then either:

1. stitch the wing straight to the body using strong thread creating a ‘cross’,
2. whip-stitch the top edge of the wing to the body which creates the best ‘flapping motion’,
3. or you can use buttons to attach your wings.

CONGRATULATIONS! 

DIY Sun Catchers

                         DIY Sun Catchers

                            

 Balloon Banner DIY

   

1) Start by grouping balloons in to groups of 4. We used rainbow colors, but using all the same color, or lots of different shades of blue would be neat too.

2) Blow up each set of 4 balloons and tie the ends. (I’m awful at tying balloons! But Maude is really good, so she was a big help.) No need for helium, your own lungs should do the trick. Do your best to get the balloons fairly equal in size.

3) Thread some good twine (I used a waxed kitchen twine) on a big needle — upholstery size is perfect. Technically, a small needle would work too, you just need the eye to be big enough to pass the twine through.

4) Pass the needle through the tail of all 4 balloons in your set. Be careful — needles are known for popping balloons. : )

5) Slide the balloons to the end of the string and trim off threaded needle and remaining length (you’ll use them to thread the next set of balloons). Leave a 2 or 3 inch tail on either side of the 4 threaded balloons.

6) Cinch the four balloons together and use a square knot (right over left, left over right) to keep them nice and tight.

7) Do the same thing for all your sets of 4. For our banner, we made 18 sets of 4. Three sets of 6 colors.

8) When you have all your sets made, thread the needle again, but don’t trim the thread from the spool.

9) Pass the needle through the center of a balloon set. Use the point to go through at least of couple of the balloon ends so that the set is secure on the twine.

10) Use the needle to add another balloon set, push each set along the twine at intervals of 5 or 6 inches. If you’re going for the same rainbow look we used, you’ll thread all the red sets first, then all the orange sets, then all the yellow sets, etc.

11) Keep adding sets with the needle and sliding them along the twine till you’ve completed your banner. Leave a long tail of twine on either side of the balloons so that you can tie the banner to a wall or arch or window. Then cut the twine from the spool.

The banner is so light that it’s easy to hang. We used push pins in the wall and then wrapped the twine around the push pins.

That’s it! You’re done. Now you can find the perfect place to hang your banner. Yay!

P.S. Here are some behind the scenes photos from the day we made June’s banner: